Inspection And Testing

Lifting equipment inspection

Lifting equipment inspection

TTS extends its service in the field of lifting equipment inspection. We have a team of qualified and experienced inspection engineers with LEEA and NDT certifications. Our services in lifting equipment inspection include

 Proof load testing or inspection (all types of cranes including tower crane, hydraulic mobile, overhead gantry, mobile crane, boom trucks and forklifts)

 Load testing of offshore cranes and barge cranes.

 Periodic inspection and certification of lifting equipment and accessories

 Testing and certification of cradles

 All types of nondestructive testing (NDT) services including magnetic particle inspection (MPI), liquid penetrant/dye penetrant examination (LP/DP), radiographic testing (RT), ultrasonic testing (UT) etc.

 Load testing and certification of man basket and man lift.

 Wire rope inspection and certification by visual and non-destructive testing methods.

Exterior windows, doors and curtain wall testing

Exterior windows, doors and curtain wall testing

TTS provides quality assurance and testing service for the exterior wall systems of large buildings. Testing is performed to British, American and other standards. The following are the tests performed by TTS for building envelopes on site

 Hose test (AAMA 501.2)

 Air permeability test (ASTM E783)

 Static water penetration test (ASTM E1105)

 Air permeability (ASTM E283 / BS EN 12153 / BS EN 1026 / CWCT / AS-NZS standards)

 Static water penetration (ASTM E331 / ASTM E547/ BS EN 12155 / BS EN 1027/ CWCT / AS-NZS Standards)

 Wind resistance tests (ASTM E330 / BS EN 12179 / BS EN12211 / CWCT/ AS-NZS standards)

Torque testing and bolt tensioning


Torque tightening test is done to check the bolt torque tightening and rotational capacity of boltsby using various calibrated standard ranges of torqueing sensors and fasteners for measuring torque values.Measuring torque is essential for companies to ensure their product’s quality, safety and reliability isn’t compromised. Insufficient torque can cause a screw or bolt to loosen from vibrations. Excessive torque can cause fasteners to overstretch and break.


The test measures the force required to pull out a previously cast in steel insert with an embedded enlarged end in the concrete. In this operation, a cone of concrete is pulled out and the force required is related to the compressive strength of concrete.This test is based on the principle that the force required to pull out a cone of steel embedded in concrete is proportional to the strength of concrete.

Heat treatment

Heat treatment

TTS offers services in heat treatment work with qualified and experienced personnel and accurate equipment’s. Our heating process includes low range, mid-range and high range temperature heating. We utilize both electrical and fuel fired method as a source of heating. We are also specialized in out side’s heat treatment by oil and gas with high velocity burners. We have high velocity burners enable excellent temperature distribution and uniformity at all times due to intense scrubbing action. We are using 50 KVA purpose built transformers for pre and post weld heating & twelve point chino chart recorders incorporating K type thermocouple to monitor work piece temperature.

Metallurgical services

Metallurgical services


TTS enhances its Nondestructive testing offering with PMI services. Our onsite inspection & testing team has multiple highly sophisticated handheld/portable x-ray fluorescence (XRF). Spectrometers can measure chemical composition of the materials (with & without carbon content) nondestructively and accurately. Using various x-ray florescence (XRF) instruments, engineers at TTS can provide elemental identification and quantitative determination without regard to form, shape & size. No samples need to be cut during PMI.

We offer services with PMI for incoming material inspection & on site alloy verification for quality control and stock control purposes. We offers services in this field to find out very minute traces of elements (parts per million-ppm, parts per billion -ppb etc.) of materials. Our services includes method development, method validation and identification of unknown materials including Aluminum alloys, Carbon, low alloys weld metals, gases, carbon & sulfur by combustion, industrial water and process solution.


We use Gravimetric (by weighing) and Titrimetric as the two procedures to perform classical chemistry. The wet chemical lab includes electro analyzers, micro wave Owen system, vacuum pump, muffle furnaces etc.


If visual inspection reveals any stud that does notshow a full 360 degree flash or any stud that has been repaired by welding, such stud shall be bent to an angle of approximately 30 degrees from its original axis.

Corrosion control services

Corrosion control services

TSS offers BGAS & NACE Certified Inspectors for Cathodic Protection (CP), Coating Inspections, Specialized Studies, Technical Consulting and nondestructive testing (NDT) services.We are equipped with maintained and calibrated instruments for coating & abrasive blasting inspection such as DFT gauges, hygrometers, surface profile measuring gauges, chloride test kits, ferrous monitor control kit, holiday testing, adhesion testing, pull of test and various others. TSS also offers services in the field of corrosion monitoring and evaluation in the field of in-service inspections.

Mechanical testing

Mechanical testing

Mechanical testing covers a wide range of tests, which can aim to determine a material's mechanical properties, independent of geometry and determine the response of a structure to a given action. These tests are standardized, to determine the various mechanical properties of materials such tests set out to obtain geometry-independent properties that is intrinsic to the bulk material. In practice this is not always feasible, since even in tensile tests, certain properties can be influenced by specimen size and/or geometry. Here is a listing of some of the most common test,

Tensile Testing

Hardness Testing

 • Vickers Hardness Test (HV)

 • Brinell Hardness Test (HB)

 • Rockwell Hardness Test (HR)

Impact Testing

Bend Tests

We are equipped with duly maintained machines calibrated to National/International standards by authorized agencies and we also provide compression testing of concrete tubs. We also perform macro examination of welds.

Specialized inspection

Specialized inspection

Manufacturers require NDT services and inspections to ensure that their plants, equipment and systems conform to the necessary standards and regulations. TSS offers Specialized Non-Destructive Testing (NDT) that helps our clients monitor and improve plant life and safety and reduces maintenance cost.

With our qualified and experienced staff we offer the following specialized services:

Phased Array Ultrasonic Testing (PA)

Time Of Flight Diffraction (TOFD)

Magnetic Flux Leakage (MFL)

 X-Ray And Gamma Ray Pipeline Crawler Inspection Systems


 Eddy Current Testing

Nondestructive testing (NDT)

Nondestructive testing (NDT)

The following nondestructive examinations services are available in TTS with technical expertise, qualified and experienced technicians and modern equipment’s. These inspection services include,

Visual Inspection

Liquid Penetrant/Dye Penetrant Examination (LPT)

Magnetic Particle Inspection (MPI)

Radiographic Testing (RT)

Ultrasonic Testing (UT)

Professionals on contract

Professionals on contract

TTS maintains a team of Third Party Inspection Personnel with all necessary equipment to the requirements of various clients. All our inspectors are qualified to either AWS CWI/CSWIP3.1 or B gas level II/III. TTS is one of the leading Manpower supply company of KUWAIT, renowned for providing recruitment and placement in almost all prominent fields like







Civil works

Information Technology



TTS provides an efficient QA consultancy service in preparing various documents like Quality Control Procedures, Inspection Test Plan (ITP), Method of Statement, Welding Procedure Specification (WPS), Procedure Qualification Record (PQR), and Welder Qualification Certificates (WQT).

We offer Third Party Services in witnessing and conducting tests for PQR - WPS&WQT and related tests required in laboratory for the same.

We also provides complete inspection services as Second/Third Party for inspections during manufacture& after erection and installation of pressure vessels, above ground steel storage tanks, pipeline, piping, and steel structures.We alsodo sampling inspection of bulk ferrous and nonferrous materials for compliance verification.

We also extent our services including supervision and inspections of both offshore and onshore facilities in various fields like civil, mechanical, electrical and industrial works.

TTS has provided these services on a wide range of projects including refineries, petrochemical plants, power plants, tanks farms, commercial steel structure buildings etc.